Made-to-fittool holders

A black 3D-printed wall rack holding six screwdrivers
Illustration of the screwdriver rack with generic tools. Not a photo of a printed part.
  • For garage walls and tool chests
  • Sized to the tools you own
  • Made to order in Burlington, Ontario
  • Pegboard 1 in grid
  • Slatwall 3 in slats
  • French cleat 45°
  • Screw-on #8 screws
  • Magnetic steel boxes
  • Drawer grid 42 mm

Tool finder

What are you organising?

Type a tool. The finder picks the part that holds it and opens the builder already set to a sensible starting size.

Tool finder

The finder needs JavaScript. Browse the shop to see every part.

The range

Everything is sized by you

Wall racks, power tool docks, drawer organisers, engraved tags and stencils. Each one starts from a preset and takes your dimensions. The newest range labels the rest of the garage: tires, shut-offs, switches, totes and keys.

Pictures are illustrations of each part's design, not photos of printed parts. Tools are shown for scale and are not included.

Power tools

One dock, any brand of drill

The tool rests on a shelf and its handle drops through a slot. You set the slot width, so the dock is cut for the drill you own.

Top view of a dock shelf. The handle of the tool sits in a slot cut 4 mm wider than the handle. shelf, seen from above front wall handle slot 46 mm · 1.81 in

46mm1.81 in slot

Size a dock

Mounts

Five ways onto the wall

Every wall holder is offered on the same five backs. Pick the one your wall or tool chest already has, and change your mind later in the builder.

1 in

Pegboard1 in grid

Hooks for 1/4 in holes on the standard 1 in (25.4 mm) grid.

For walls that already have pegboard up.

3 in

Slatwall3 in slats

A lip that drops into standard 3 in (76.2 mm) slatwall grooves.

For slatwall panels and rails.

45°

French cleat45°

Comes with a matching 45° wall strip. Lift it off any time.

For heavier tools and walls you rearrange.

#8

Screw-on#8 screws

Countersunk holes for #8 screws, into a stud, plywood or a bench.

For bare walls and workbenches.

steel

Magneticsteel boxes

Recessed magnets for steel tool chests and cabinets. No holes.

For the side of a tool chest.

Drawings are side views: the wall is on the left, the holder in black, your tool dashed.

See the wall holders

How ordering works

You pay after we check the fit

  1. Build it

    Set the sizes, mount and colour in the builder. The 3D preview and the price update as you go.

  2. We check and confirm

    Send the order request from your cart. We check the fit against your measurements, then email the confirmed price and ship date.

  3. Then you pay

    No payment is taken on this site. You pay once you have the confirmed price and ship date in hand.

Starter kits

Start with a set

Four starting points built from catalogue parts. Open any piece in the builder to change its size, or add the whole set to your cart and edit from there.

Questions

Something else? Call us or email the shop.

Will it fit my brand of drill?

Yes, if you can measure it. Docks are not made for a list of models: the handle slot is cut to the width you enter. Add the brand and model in the builder and we check the fit before printing.

When do I pay?

After we confirm. You send an order request from the cart, and no payment is taken on this site. We check the fit, then email the confirmed price and ship date. You pay once you have both.

How long does an order take?

Engraved tags usually leave in 1–3 business days. Printed parts are quoted at 3–7 business days for now, and that figure is still being settled. Either way, we confirm the ship date by email before any payment.

Which mount should I pick?

Match what is already on the wall: pegboard with 1/4 in holes on a 1 in (25.4 mm) grid, 3 in (76.2 mm) slatwall, or a French cleat. Screw-on suits bare studs, plywood and benches. Magnetic suits steel tool chests and cabinets. Heavier tools are best on screws or a cleat.

What is the 42 mm drawer grid?

Drawer bins, socket trays and baseplates share one 42 mm (1.65 in) grid. A baseplate lines the drawer, and anything sized in grid units locks onto it, so the drawer can be rearranged later without buying again.

What if my tool is not in the finder?

Start from the closest shape. Hooks, shelves, rings and bins take whatever size you enter, so most tools fit one of them. If you are not sure which, call or email us with what you are trying to hang.

Can a stencil match my exact tools?

The outline stencils in the shop are generic shapes. For outlines of your own tools, send a photo of them on a flat surface with a ruler in frame and we will trace them.

Do you ship outside Burlington?

Yes. Everything is made to order in Burlington, Ontario and ships Canada-wide.

Who makes these?

Peg & Plate is the garage and toolbox line from Llamacoids Inc, the Burlington, Ontario shop that engraves identification tags for electrical work. Same people, same bench, same phone number: 289-275-9572.

Are the prices on the site final?

Not yet. They are placeholders while materials and print times are settled. The price that counts is the one we email you before you pay.

Are the product images photos?

No. The product pictures are illustrations of each part's design, and the builder draws your version live from its real dimensions. Tools appear for scale in common brand colours and are not included.

A place for every tool you own